RIVOWON PVC Handle Patch with woven strap for gluing onto inflatable boats and SUPs

Adhesive PVC Handle Patch for Inflatable Boats and SUPs

Name: RIVOWON Inflatable Boat Handle Patch – Glue-On PVC Base with Heavy-Duty Carry Strap for DIY Kayak, Dinghy & SUP Upgrade
Rating: 5.00 (11 reviews)

$5.00

Add a Handle Exactly Where You Need It.

Struggling to carry or drag your inflatable boat because the factory handles are in the wrong spot — or missing entirely? The RIVOWON Inflatable Boat Handle Patch lets you add a rock-solid, heavy-duty carry handle anywhere on your hull. Whether you're replacing a torn handle or upgrading your kayak for easier solo transport, this is the simple, permanent fix.

📌 Glue-On PVC Base – No Drilling, Pure Strength

High-quality thickened PVC base is designed to bond directly and permanently to your PVC inflatable boat using standard marine PVC adhesive (glue not included).
Creates a massive contact area for superior bond strength, ensuring the handle won't peel off under the heavy weight of a fully loaded boat.

💪 Heavy-Duty Woven Carry Strap

Tough, wear-resistant woven webbing with reinforced stitching provides outstanding load-bearing capacity.
Comfortable and wide enough to prevent digging into your hands when lifting, dragging, or launching your watercraft.

📏 31cm Overall Length – Universal Fit

At 31cm (12.2 inches) in overall length, it provides plenty of grip room even when wearing thick neoprene gloves.
Widely compatible with most inflatable dinghies, kayaks, SUPs, and small rubber tenders.

🎨 Match Your Boat

Available in Black and Gray to seamlessly match your boat’s factory trim or hull color for a clean, professional look.

🔧 Easy DIY Installation

Simply clean the bonding surface, apply PVC marine adhesive evenly, and press firmly into place. Wait to cure, and you’re ready to haul.

Grab it. Lift it. Launch it. That’s RIVOWON.

These worked great for my spare board I have for guests. It didn't have any handles on it and my guests and I found it quite frustrating so I added these - one at the front and one at the back. Since then it's been a lot easier to get in and out of the water with it and to help hold the board for others when they need it.

I bought the two carrying handles to install them on my inflatable kayak.

These are quality handles for an inflatable vote. You must read the directions. Make sure you're used to correct anhesive. But other than that I am hiding satisfied. I actually wouldn't bought another pair for my other inflatableabout 12 minutes.

I purchased these handled to modify a generic paddleboard that had none. They are of good quality material, sturdy straps, and adhered well to my paddleboard with HH-66 vinyl cement. Have not tested the handles in water yet, but I also used the vinyl cement to apply extra D-rings last year and they work great! That said, I am confident that as sturdy as these straps are, they will be great. I may buy another set soon for my spare paddleboard

Seem durable and holding up well so far. These handles were used on my inflatable traveling kayak. The webbing handlings allow for the rolling up and packing of the kayak, once inflated permits for a secure handle when lifting and moving the kayak.

Make sure to properly prep and clean, and with the correct adhesive you should have a durable handle in place.

These are excellent quality and priced perfectly!

I finally installed them! They are good straps/ handles. Good quality strap.

It works so I gave it a 5 star. Only needed a single handle but the price was right and I have a spare in case I buy another board or need to replace one on another board. It works=5 stars.

I added one front handle strap to each of my 2 paddleboards and it worked out very well. You have to use Vinyl cement and apply it to both the paddleboard and the handle and then stick them together but it's a very strong permanent bond.